Arduino Single power control unit - Revision history

Plauchu Edwin at 18:50, 14 December 2016

2016-12-14T18:50:56Z

← Older revision		Revision as of 18:50, 14 December 2016
Line 1:		Line 1:
	== The Justification ==		== The Justification ==
	The Arduino Single power control unit was created for controlling a relay that is able to turn on/off the devices that it powers like the Yocto DUTs. Such need has arisen due to a clean power-off has not been always reliable.		The Arduino Single power control unit was created for controlling a relay that is able to turn on/off the devices that it powers like the Yocto DUTs. Such need has arisen due to a clean power-off has not been always reliable.

	~~== The software part ==~~
	~~It is required '''devauto''' module '''simplepwsc''' to control this single power unit. Upon the source directory of this module can be found '''gen_ard_101.ino''' to flash the arduino 101~~

	== The hardware part ==		== The hardware part ==
Line 30:		Line 27:
	* GND (from the board)		* GND (from the board)
	* Signal (min 3.3V max 5V, from GPIO 13 of board)		* Signal (min 3.3V max 5V, from GPIO 13 of board)


			== The software part ==
			It is required '''devauto''' module '''simplepwsc''' to control this single power unit. Upon the source directory of this module can be found '''gen_ard_101.ino''' to flash the arduino 101

2016-12-14T18:50:01Z

The arduino 101

← Older revision		Revision as of 18:50, 14 December 2016
Line 26:		Line 26:
	[[File:Arduino.jpg]]		[[File:Arduino.jpg]]

	Configuration for power cutter cables upon Arduino 101:		==== Configuration for power cutter cables upon Arduino 101 ====
	* 5V (from the board)		* 5V (from the board)
	* GND (from the board)		* GND (from the board)
	* Signal (min 3.3V max 5V, from GPIO 13 of board)		* Signal (min 3.3V max 5V, from GPIO 13 of board)

2016-12-14T18:49:42Z

The arduino 101

← Older revision		Revision as of 18:49, 14 December 2016
Line 27:		Line 27:

	Configuration for power cutter cables upon Arduino 101:		Configuration for power cutter cables upon Arduino 101:
	5V (from the board)		* 5V (from the board)
	GND (from the board)		* GND (from the board)
	Signal (min 3.3V max 5V, from GPIO 13 of board)		* Signal (min 3.3V max 5V, from GPIO 13 of board)

2016-12-14T18:49:19Z

The arduino 101

← Older revision		Revision as of 18:49, 14 December 2016
Line 26:		Line 26:
	[[File:Arduino.jpg]]		[[File:Arduino.jpg]]

	Configuration for ~~relay~~ cables:		Configuration for power cutter cables upon Arduino 101:
	5V (from the board)		5V (from the board)
	GND (from the board)		GND (from the board)
	Signal (min 3.3V max 5V, from GPIO 13 of board)		Signal (min 3.3V max 5V, from GPIO 13 of board)

2016-12-14T18:48:04Z

the required hardware

← Older revision		Revision as of 18:48, 14 December 2016
Line 12:		Line 12:
	[[File:housemade_relay.png]]		[[File:housemade_relay.png]]

	==== ~~the~~ required hardware ====		==== The required hardware ====
	* 1 BJT transistor 2N2222A		* 1 BJT transistor 2N2222A
	* 1 3.3 kOhms resistor		* 1 3.3 kOhms resistor
Line 21:		Line 21:
	* 1 male outlet connector and 1 female outlet plug		* 1 male outlet connector and 1 female outlet plug
	* 14AWG Wire (as needed)		* 14AWG Wire (as needed)


	=== The arduino 101 ===		=== The arduino 101 ===

2016-12-14T18:47:29Z

The arduino 101

← Older revision		Revision as of 18:47, 14 December 2016
Line 26:		Line 26:

	[[File:Arduino.jpg]]		[[File:Arduino.jpg]]

			Configuration for relay cables:
			5V (from the board)
			GND (from the board)
			Signal (min 3.3V max 5V, from GPIO 13 of board)

2016-12-14T18:43:06Z

The hardware part

← Older revision		Revision as of 18:43, 14 December 2016
Line 6:		Line 6:

	== The hardware part ==		== The hardware part ==
	~~=== The arduino 101 ===~~

	~~[[File:Arduino.jpg]]~~

	=== The circuit ===		=== The circuit ===
Line 24:		Line 21:
	* 1 male outlet connector and 1 female outlet plug		* 1 male outlet connector and 1 female outlet plug
	* 14AWG Wire (as needed)		* 14AWG Wire (as needed)


			=== The arduino 101 ===

			[[File:Arduino.jpg]]

2016-12-14T18:39:21Z

The Justification

← Older revision		Revision as of 18:39, 14 December 2016
Line 1:		Line 1:
	== The Justification ==		== The Justification ==
	The Arduino Single power control unit was created for controlling a relay that is able to turn on/off the devices that it powers like the Yocto DUTs. Such need has arisen due to a clean power-off is not always reliable.		The Arduino Single power control unit was created for controlling a relay that is able to turn on/off the devices that it powers like the Yocto DUTs. Such need has arisen due to a clean power-off has not been always reliable.

	== The software part ==		== The software part ==

2016-12-14T18:38:27Z

The software part

← Older revision		Revision as of 18:38, 14 December 2016
Line 3:		Line 3:

	== The software part ==		== The software part ==
	It is required devauto module 'simplepwsc' to control this single power unit. Upon the source directory of this module can be found gen_ard_101.ino to flash the arduino 101		It is required '''devauto''' module '''simplepwsc''' to control this single power unit. Upon the source directory of this module can be found '''gen_ard_101.ino''' to flash the arduino 101

	== The hardware part ==		== The hardware part ==

2016-12-14T18:36:44Z

The arduino 101